{ "id": "2-bike-gravity-stand", "sku": "2-bike-gravity-stand", "title": "2 Bike Gravity Stand", "slug": "2-bike-gravity-stand", "price": 342.99, "currency": "NZD", "availability": "in_stock", "category": "bike-stand", "category_label": "Bike Stands", "tags": [], "colors": [], "materials": [], "dimensions": null, "weight": "113 g", "images": [ "https://bikestand.co.nz/dropship-images/bike-stand/2-bike-gravity-stand/main-2-bike-gravity-stand.jpg", "https://bikestand.co.nz/dropship-images/bike-stand/2-bike-gravity-stand/2-bike-gravity-stand-2.jpg", "https://bikestand.co.nz/dropship-images/bike-stand/2-bike-gravity-stand/2-bike-gravity-stand-3.jpg", "https://bikestand.co.nz/dropship-images/bike-stand/2-bike-gravity-stand/2-bike-gravity-stand-4.jpg", "https://bikestand.co.nz/dropship-images/bike-stand/2-bike-gravity-stand/2-bike-gravity-stand-5.jpg", "https://bikestand.co.nz/dropship-images/bike-stand/2-bike-gravity-stand/2-bike-gravity-stand-8.jpg" ], "description_short": "Adjustable arms suit most frame shapes, a silver powder coat finish resists scratches, and the alloy steel frame holds up to 36 kg (80 lb) across two levels.", "description": "The problem with two bikes and one small house\n\nTwo bikes in a home that was not designed for bikes is a daily annoyance. They lean on the hallway wall and leave black marks from the pedals. They fall sideways when someone brushes past with shopping. In a garage they end up wedged between the car and the shelving, and getting one out means moving the other first.\n\nWall mounted hooks solve this, but only if you can drill. Plenty of people cannot. Renters are not allowed to put anchors in plasterboard. Owners sometimes face brick, tile, or a nicely finished wall they would rather not punch holes in. That is the gap a leaning bike rack fills.\n\nA gravity stand is a tall upright with a wide foot. It tilts back against the wall, and once you load bikes onto its arms, their weight presses it in place. The whole thing sits in a strip of floor roughly the depth of a bookshelf. Two bikes stack one above the other, out of the walkway, off the paintwork, and easy to grab.\n\nIt is an alloy steel upright, 213 cm tall and 66 cm wide, finished in a silver powder coat. Two pairs of arms stick out from the upright. Your bikes rest on them by their top tubes or frames, one high, one low.\n\nThe arms are the easy-adjust type. They slide up and down the upright so you can set the gap between bikes to match the two you own. That matters more than it sounds. A road bike with a long horizontal top tube and a modern mountain bike with a steeply sloping one need very different arm heights to sit level. Being able to move them means you are not stuck with whatever spacing the factory chose.\n\nTotal rated capacity is 36 kg (80 lb). Read that as a combined number, not per bike. Two road bikes together are usually well under it. Two steel touring bikes with racks and panniers on, or an e-bike plus anything else, may not be.\n\nStability comes from three things working together. The base width stops it tipping sideways. The lean angle pushes the top into the wall. And the bikes themselves add weight low and forward, which is why these stands feel noticeably more solid loaded than they do empty.\n\nWho it suits\n\nRenters get the most obvious benefit. There is nothing to fix, nothing to patch, and nothing to argue about at the end of a lease. If you have been hunting for the best no drill bike rack, this category is basically the answer.\n\nIt also suits anyone with a difficult wall. Brick, concrete block, tiled surfaces and rendered garage walls are all hard work to drill, and a gravity stand sidesteps that completely. Same for people who share a wall with a neighbour and would rather not deal with the noise or the uncertainty of what is behind the plaster.\n\nHouseholds with two regular riders get good value from it. Each bike has its own level, so neither one has to be lifted out of the way to reach the other. Mixed households work too, with an adult bike down low and a smaller bike above.\n\nIt is less suited to a few situations. Very low ceilings rule it out at 213 cm tall. Heavy e-bikes push against both the weight limit and the practical difficulty of lifting them chest high. And if your only free wall is a flimsy partition or a sloped attic wall, you want a different solution.\n\nChoosing the right spot\n\nStart with a tape measure. You need 213 cm of clear height, allowing for light fittings, shelf edges and garage door tracks. You need about 66 cm of flat wall width, and roughly 41 cm of floor depth before you count the bikes themselves, which stick out further.\n\nPick a wall without skirting board that juts out at the top or any trim that would stop the frame sitting flush. Corners are good. So is the dead space behind a door or at the end of a hallway. In a garage, the wall furthest from the car door swing is usually the right call.\n\nThink about the floor too. Hard floors like concrete, tile or timber give the most reliable footing. Carpet works, but the base settles into the pile, so load it and check the lean before you trust it. If anyone in the house is likely to knock into it, choose a spot out of the main traffic route.\n\nFinally, think about which bike goes where. The heavier bike belongs on the lower arms. That keeps the centre of gravity low and saves you lifting the heavy one to shoulder height every time you ride.\n\nSetting it up\n\nAssembly is required and the hardware comes in the box. Build the upright and base on the floor first, then stand it up and lean it into position before you finalise the arm heights. It is much easier to judge spacing with the stand where it will actually live.\n\nLoad the lower bike, then adjust the upper arms so the top bike's pedals, bars and saddle clear everything below. Most people stagger the two bikes nose to tail. One faces left, one faces right. That stops handlebars tangling and makes each bike easier to pull out on its own.\n\nOnce it is set, check the lean. The upright should rest against the wall with the base flat on the floor and no rocking. Give it a gentle push to confirm it settles back rather than skating. Then load, unload, and reload a couple of times so the motion becomes natural.\n\nLooking after it\n\nThere is not much to do. Wipe the frame with a dry or slightly damp cloth now and then, and dry it off. Strong solvents and abrasive pads will dull the powder coat, so leave those in the cupboard.\n\nKeep the arms clean. Grit and chain grime that collects on an arm is what ends up pressed against your frame, so a quick wipe after a muddy ride protects your paint more than anything else. Every few months, check the arm clamps and fasteners and nip up anything that has worked loose.\n\nKeep it indoors. It is listed for indoor use only, and a steel frame left in the weather will find a chip to start rusting from.\n\nThe short version\n\nIf you own two bikes and cannot or will not drill into your walls, a gravity stand is the practical answer. Total capacity is 36 kg (80 lb), height is 213 cm, and the finish is a scratch resistant silver powder coat.\n\nMeasure your ceiling, weigh your bikes, pick a solid wall, and put the heavy bike on the bottom. Do those four things and you will stop tripping over bikes in the hallway for good.", "llm_summary": "The 2 bike gravity stand is made of alloy steel with a silver powder coat finish described as scratch resistant, and it leans against a wall rather than being drilled or bolted to it. Easy-adjust arms slide to suit different frame shapes. Rated capacity is 36 kg (80 lb) and the product measures 40.6 cm deep by 66 cm wide by 213 cm tall. Listed item weight is 113 g. Assembly is required and the needed hardware is included. Colour is silver.", "returnable": true, "return_policy": "Change-of-mind returns accepted for 15 days from delivery under this shop's own published policy: original packaging, proof of purchase, buyer pays return postage. The guarantees of the Consumer Guarantees Act 1993 apply to faulty or misdescribed goods, with repair, replacement or refund and return postage covered by the shop.", "shipping_profile": "standard", "warranty": null, "brand": "Bike Stand Company", "gtin": null, "mpn": null, "condition": "new", "url": "https://bikestand.co.nz/product/2-bike-gravity-stand/", "canonical_url": "https://bikestand.co.nz/product/2-bike-gravity-stand/", "json_url": "https://bikestand.co.nz/api/products/2-bike-gravity-stand.json", "updated_at": "2026-11-08", "compare_at_price": 411.99 }